1. Cat Grader 14h Manual Transmission
  2. Cat 14h Specs
  3. Cached
  4. Cat 14h Motor Grader Specs
  5. Cat 14h Weight

This Caterpillar 14H Motor Graders service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting) is divided into different sections. Each section covers a specific component or system with detailed illustrations. Inspection Cat 14H Grader. This Caterpillar 12H, 140H & 160H Motor Graders service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting) is divided into different sections. Each section covers a specific component or system with detailed illustrations. Caterpillar 14H Motor Grader Compressor Clutch with Coil - New Caterpillar 14H Air Conditioning(Replacement Clutch For Compressor 883E1906)5.35', 1 Groove, 24 Volt.

Piston Pump Cutoff Pressure (Hydraulic Fan) - Test and Adjust

Cat 14h for sale

The drive shaft rotates between the torque converter and the transmission whenever the engine is running. Contact with the rotating shaft can result in personal injury or death. The rotating shaft is located under the implement and steering pumps.

Do not allow personnel into the pump bay area behind the cab when the engine is running.

Show/hide table

Sudden movement or accidental starting of the machine can cause personal injury or death to persons on or near the machine.

To prevent personal injury or death, perform the following:

Park the machine on a smooth, level surface.

Lower the work tool to the ground and engage the parking brake.

Stop the engine and remove the key.

Block the wheels and install the steering frame lock.

The fan drive pump is a variable displacement piston pump. There is no pressure relief valve in the fan drive system. The pressure and flow compensator valve on the pump controls the pump cutoff pressure. The pressure and flow compensator valve also controls the flow of hydraulic oil to the fan drive motor.

The Caterpillar Electronic Technician (ET) software must be used in order to override fan speed solenoid (5). Caterpillar ET will then provide the correct control pressure to the pump control. The fan speed solenoid is controlled by the engine ECM.

Note: Caterpillar ET is a software program that can be used on an IBM compatible personal computer.

14h
Table 1
Required Tools
Part NumberDescriptionQuantity
8T-0860 Pressure Gauge 1
6V-3989 Unvalved Nipple 1
1U-6602 Photo-Tachometer 1

Before proceeding to the test procedure that follows, complete the procedure: Testing and Adjusting, 'Machine Preparation for Troubleshooting'

Show/hide table

Cat Grader 14h Manual Transmission

Illustration 1g01062907
View of the components under the cab
(1) Pressure tap for output pressure of the fan drive
(2) Margin pressure adjusting screw
(3) Locknut for margin pressure adjusting screw
(4) Pump control valve
(5) Fan speed solenoid
(6) Cutoff pressure adjusting screw
(7) Locknut for Cutoff pressure adjusting screw
(8) Fan drive pump

The fan drive pump is located in the front of the pump compartment. The pump compartment is on the front frame under the operator compartment. The fan drive pump is in line with the hydraulic and steering pump.

  1. Engage the parking brake.
  2. Attach an unvalved nipple to a 0 to 16000 kPa(0 to 2321 psi) pressure gauge. Attach a section of hydraulic line to the unvalved nipple. Attach the hydraulic line to pressure tap (1).
  3. Shift the transmission to neutral.
  4. Start the engine. Run the engine at high idle.
  5. Move the wheel lean cylinder to the end of the stroke. Stall the cylinder. At the same time, circle the moldboard. This will warm the hydraulic oil to normal operating temperature of approximately 60° ± 5°C(140° ± 9°F).
  6. Connect Caterpillar ET to the data link connector. The data link connector is located on the front face of the shift console. Start Caterpillar ET.
  7. Select the 'File' menu. From the 'File' menu, select the engine 'Electronic Control Module (ECM)' for your machine. Select 'Diagnostics'. Select 'Diagnostic Tests'. Select 'Override Parameters'. Select 'Engine Fan Bypass'.
  8. Enter '0%' for the 'Engine Fan Bypass Override Parameter'. Press 'Enter' until all warning messages disappear. This will cause the fan to run at maximum speed when the engine is at high idle.
  9. With the engine at high idle, use the 1U-6602 Photo-Tachometer in order to measure the fan speed. The pressure reading of the pressure gauge should be used as reference only. Use the following table in order to determine the correct fan speed and reference pressure.
    Table 2
    Fan Speeds
    Model Fan SpeedReference Pressure
    14H 1210 ± 25 RPM 8000 ± 500 kPa(1160 ± 73 psi)
    14H High Ambient 1350 ± 25 RPM 10000 ± 500 kPa(1450 ± 73 psi)
    16H 1350 ±25 RPM 10000 ± 500 kPa(1450 ± 73 psi)
    16 High Ambient 1470 ±25 RPM 11840 ± 500 kPa(1717± 73 psi)
  10. If the pump cutoff pressure of the fan drive pump is not correct, the cutoff valve must be adjusted.
  11. Stop the engine.
  12. Loosen locknut (7).
  13. Turn adjusting screw (6) clockwise in order to increase the pressure setting. Turn adjusting screw (6) counterclockwise in order to decrease the pressure setting.
  14. Tighten locknut (7).
  15. Start the engine.
  16. Repeat Step 7 through Step 15 until the proper fan speed is obtained.
  17. Use Caterpillar ET in order to reset the 'Engine Fan Bypass Override Parameter'.
  18. Exit the Caterpillar ET program and disconnect ET from the machine.

Cat 14h Specs

Piston Pump Cutoff Pressure (Hydraulic Fan) - Test and Adjust
14h

Cached


The drive shaft rotates between the torque converter and the transmission whenever the engine is running. Contact with the rotating shaft can result in personal injury or death. The rotating shaft is located under the implement and steering pumps.

Do not allow personnel into the pump bay area behind the cab when the engine is running.

Show/hide table

Sudden movement or accidental starting of the machine can cause personal injury or death to persons on or near the machine.

To prevent personal injury or death, perform the following:

Park the machine on a smooth, level surface.

Lower the work tool to the ground and engage the parking brake.

Stop the engine and remove the key.

Block the wheels and install the steering frame lock.

The fan drive pump is a variable displacement piston pump. There is no pressure relief valve in the fan drive system. The pressure and flow compensator valve on the pump controls the pump cutoff pressure. The pressure and flow compensator valve also controls the flow of hydraulic oil to the fan drive motor.

Cat 14h Motor Grader Specs

14h

The Caterpillar Electronic Technician (ET) software must be used in order to override fan speed solenoid (5). Caterpillar ET will then provide the correct control pressure to the pump control. The fan speed solenoid is controlled by the engine ECM.

Note: Caterpillar ET is a software program that can be used on an IBM compatible personal computer.

Table 1
Required Tools
Part NumberDescriptionQuantity
8T-0860 Pressure Gauge 1
6V-3989 Unvalved Nipple 1
1U-6602 Photo-Tachometer 1

Before proceeding to the test procedure that follows, complete the procedure: Testing and Adjusting, 'Machine Preparation for Troubleshooting'

Cat 14h Weight

Show/hide table
Illustration 1g01062907
View of the components under the cab
(1) Pressure tap for output pressure of the fan drive
(2) Margin pressure adjusting screw
(3) Locknut for margin pressure adjusting screw
(4) Pump control valve
(5) Fan speed solenoid
(6) Cutoff pressure adjusting screw
(7) Locknut for Cutoff pressure adjusting screw
(8) Fan drive pump
Cat Grader 14h Manual

The fan drive pump is located in the front of the pump compartment. The pump compartment is on the front frame under the operator compartment. The fan drive pump is in line with the hydraulic and steering pump.

  1. Engage the parking brake.
  2. Attach an unvalved nipple to a 0 to 16000 kPa(0 to 2321 psi) pressure gauge. Attach a section of hydraulic line to the unvalved nipple. Attach the hydraulic line to pressure tap (1).
  3. Shift the transmission to neutral.
  4. Start the engine. Run the engine at high idle.
  5. Move the wheel lean cylinder to the end of the stroke. Stall the cylinder. At the same time, circle the moldboard. This will warm the hydraulic oil to normal operating temperature of approximately 60° ± 5°C(140° ± 9°F).
  6. Connect Caterpillar ET to the data link connector. The data link connector is located on the front face of the shift console. Start Caterpillar ET.
  7. Select the 'File' menu. From the 'File' menu, select the engine 'Electronic Control Module (ECM)' for your machine. Select 'Diagnostics'. Select 'Diagnostic Tests'. Select 'Override Parameters'. Select 'Engine Fan Bypass'.
  8. Enter '0%' for the 'Engine Fan Bypass Override Parameter'. Press 'Enter' until all warning messages disappear. This will cause the fan to run at maximum speed when the engine is at high idle.
  9. With the engine at high idle, use the 1U-6602 Photo-Tachometer in order to measure the fan speed. The pressure reading of the pressure gauge should be used as reference only. Use the following table in order to determine the correct fan speed and reference pressure.
    Table 2
    Fan Speeds
    Model Fan SpeedReference Pressure
    14H 1210 ± 25 RPM 8000 ± 500 kPa(1160 ± 73 psi)
    14H High Ambient 1350 ± 25 RPM 10000 ± 500 kPa(1450 ± 73 psi)
    16H 1350 ±25 RPM 10000 ± 500 kPa(1450 ± 73 psi)
    16 High Ambient 1470 ±25 RPM 11840 ± 500 kPa(1717± 73 psi)
  10. If the pump cutoff pressure of the fan drive pump is not correct, the cutoff valve must be adjusted.
  11. Stop the engine.
  12. Loosen locknut (7).
  13. Turn adjusting screw (6) clockwise in order to increase the pressure setting. Turn adjusting screw (6) counterclockwise in order to decrease the pressure setting.
  14. Tighten locknut (7).
  15. Start the engine.
  16. Repeat Step 7 through Step 15 until the proper fan speed is obtained.
  17. Use Caterpillar ET in order to reset the 'Engine Fan Bypass Override Parameter'.
  18. Exit the Caterpillar ET program and disconnect ET from the machine.

⇐ ⇐ Lacie Drive Icons For Mac
⇒ ⇒ Star Wars Care Package