Foxmoney320

1. Remington Rolling Block Rifle Serial Numbers
2. Remington Model 4 Serial Numbers
3. Remington Rolling Block Production Numbers

Remington New Model 4 Takedown Rifle.22 short, long, LR caliber 22 1/2' octagon barrel Rolling block Single shot Made 1890-1933 Total of 356,000 made V-notch rear sight with bead.Click for more info. The #4 Remington rolling block is the smallest of the rolling block rifles. It was only produced in rim fire cartridges and may be found in the three variations shown here plus military and Boy Scout models. The quickest identifying feature is the mounting of Breech Block and Hammer on screws rather than pins. Remington Rolling Block Rifle Serial Numbers Posted By admin On 24/05/18 Frank de Haas in Single Shot Rifles and Actions shows the dates of manufacture for the #4 model Remington rolling block as 1890 to 1933. The first type being the rigid frame with screw in barrel. The Remington Model 4 is a rolling block, solid-breech, hammerless, takedown, top-ejection rifle. This gun, designed by F.A. Simpson, and O.H. Loomis, was introduced in 1890 and produced through 1933.During the 43-year period, there were 356,000 guns sold.The gun featured a rolling block action and competed quite successfully for accuracy and reliability with the Winchester guns.

32 remington serial number. Registered Users do not see the above ad. I'll take a WAG, and say that you have a Remington #4 Rolling Block Boy's Rifle, since the earlier ones were made with 22' octagonal bbls (measured inside the bore, from muzzle to face of closed breech).

Remington M1867
Swedish rifle m/1867. Pattern (Modellexemplar), serial # 1
Type
Place of origin	United States Sweden Norway
Service history
In service	1867–mid-1890s (rifle) 1888–1908 (modified carbines)
Production history
Designer	Joseph Rider
Designed	1867
No. built	Remington, USA: 10,000 rifles Sweden: 237,000-257,000 rifles and carbines, including conversions of older rifles to rolling block. About 5,000 of the rifles made in Sweden were delivered to Norway while the rest of the production was for Sweden Norway: 53,450 rifles (of which 5,000 were later converted to carbines)
Variants	Sweden: Among others rifles m/1867, m/1867-68, m/1860-67, m/1864-68 and carbines m/1870 and m/1864-68-85[1] Norway: M1867, M1888 & 1891 Carbine conversions
Specifications
Mass	Rifle: 4,32 kg, 9.6 lb Carbine: 2.88 kg 6.3 lbs
Length	Rifle 1353 mm, 53.27 in Carbine (m/1870): 860 mm, 33.86 in[2]
Barrel length	Rifle: 951 mm, 37.44 in Carbine (m/1870): 460 mm, 18.11 in
Cartridge	12.17×42mm RF rimfire 12.17×44mm RF rimfire 12.17×44mmR centerfire 10.15×61mmR Jarmann centerfire 8×58mmR Danish Krag centerfire
Action	Rolling block
Rate of fire	13 rounds/minute
Muzzle velocity	Original rifles and carbines in 12.17 mm Rifle: 386 m/s, 1,266 ft/s[3] Carbine: 340 m/s, 1,115 ft/s[2]
Effective firing range	900 m, 3000 ft
Feed system	NA
Sights	V-notch and front post

The Model 1867 Remington rolling block rifle was the first rifle using metallic cartridges to be adopted by the Swedish and Norwegian armies. Nominally it had a caliber of 4 decimal lines, but the actual caliber was 4.1 Swedish decimal lines or 3.88 Norwegian decimal lines (12.17 mm), and it fired a rimfire round with a 12.615 mm (.497 in) lead bullet. The 12.17 mm caliber was chosen because the Swedish army had approximately 30,000 new muzzle-loading Model 1860 and breech-loading Model 1864 rifles in 12.17 mm caliber in stock, rifles that were suitable for conversion to Model 1867 rolling block rifles. With the exception of the first 10,000 rifles and 20,000 actions (for conversions of older rifles), which were made by Remington in the US, all Model 1867 Remington rolling block rifles and carbines were made under license in Sweden and Norway, by Carl Gustafs stads Gevärsfaktori and Husqvarna Vapenfabriks Aktiebolag in Sweden and by Kongsberg Vaapenfabrik in Norway, with the two Swedish manufacturers producing about 80% of the weapons.

Birth of the M1867[edit]

In the 1860s the Swedish and Norwegian armies realized that their standard rifles, both percussion lock breech-loading rifles and muzzle loaders, were rapidly becoming obsolete in the face of the new metal cartridge combining bullet, primer and propellant load. In early October 1866, a joint Swedish-Norwegian arms commission was established in order to select a suitable cartridge and rifle for the two nations.

Several different cartridges and rifles were considered by the commission. A partial list includes:

• A Prussian needle gun designed in 1866.
• Larsen and Steenstrup - two different modifications of the standard issue army rifle at the time.
• A modified Swedish standard army rifle.

• Non-repeating rifles for metallic cartridges:

• Peabody - American lever-action
• Remington - American, rolling block
• Larsen - two related, but different Norwegian designs. One lever-action, one bolt action

• Repeating rifles for metallic cartridges:

• Spencer - American design, removable magazine in the buttstock
• Henry - American design, tubular magazine under the barrel
• Larsen - Norwegian modification of the Henry

• Repeating rifles for paper cartridges:

• Palmcrantz - Swedish design (See Helge Palmcrantz)

• Percussion rifles:

• Burnside - American design with metallic cartridge
• Sharps - American design using paper cartridges

After various tests, including repeated firings, it was clear that the needle guns were not particularly well-suited. These - along with the repeating rifles - were dropped from further testing. Further testing - which included test firing by previously untrained troops - showed that both the Peabody and the Remington was suitable for issuing to the field army. In the end, the commission based their decision on price and complexity. The Remington totalled a mere 25 parts to the Peabody's 37, and it was approved for use by both the Swedish and the Norwegian armed forces, as their standard military rifle, on 22 November 1867.

The M1867 in Sweden[edit]

About 200,000-220,000 military rifles and 7,000 military carbines using the m/1867 action were manufactured as complete weapons in Sweden, 100,000-120,000 rifles and 4,000 carbines by Carl Gustafs Stads Gevärsfaktori (a government owned arsenal) and 100,000 rifles and 3,000 carbines by Husqvarna Vapenfabriks Aktiebolag.^[4] In addition to that 10,000 complete rifles and 20,000 actions made in the US were bought from Remington. The standard rifle received the Swedish designation 'gevär m/1867' (and a version with only minor differences the designation 'gevär m/1867-68'). Approximately 30,000 Swedish muzzle-loading rifles m/1860 and breech-loading rifles m/1864 (some of which had been converted from m/1860; note that the Swedish breech-loading rifle m/1864 although being referred to as a 'kammarladdare' was not the same rifle as the Norwegian Kammerlader) of the same caliber, rifles that were almost new and in most cases had never been used, were also converted to M1867 Remington rolling block using actions made both by Remington and in Sweden. The Swedish designations for the converted rifles were 'gevär m/1860-68', 'gevär m/1864-68' and 'gevär m/1860-64-68' depending on how many steps of conversion they had gone through (the two latter conversions are easily recognized by having the rear sight very far back, a result of the barrels being shortened from the breech end).^[5] About 7,000 short carbines with the Swedish designation 'karbin m/1870' were also made, and in addition to that about 9,600 'gevär m/1864-68' were shortened to carbine length in 1886-87 and given the designation 'karbin m/1864-68-85'.^[4] Other varieties were 'gevär m/1867-74' with a new rear stock design and 'kammarskjutningsgevär m/1884' and 'kammarskjutningskarbin m/1884' in 10,15x61R Jarmann (rifles and carbines primarily used for gallery shooting, that is short range training).^[5]

Both M1867's for civilian use and M1867's used by the Swedish Frivilliga Skarpskytterörelsen ('The Volunteer Sharpshooter Movement', patterned on the British Volunteer Force and numbering 40,000 men in 1865; all of them wearing military style uniforms and provided with military rifles by the Swedish armed forces) were made for, or converted to, centerfire 12.17×44mmR cartridges since, unlike the 12.17×42mm rimfire cartridges used in the military, the centerfire cartridges could be reloaded. One model of Swedish military M1867 rifles modified to use the 12.17×44mmR centerfire cartridge was the 'gevär m/1867-74'.^[6]

A new Swedish-Norwegian arms commission set up in the 1880s suggested that the Norwegian M1884 Jarmann rifle should replace the m/1867 in both Swedish and Norwegian service but the Jarmann rifle was rejected by the Swedish Army since the 10.15x61mmR cartridge used by the Jarmann rifle was seen as being too little of an improvement over the 12.17 mm cartridge used in the Model 1867 rifles. So as a stop-gap measure rifles and carbines with rolling block action were converted to a for that time period very modern centerfire cartridge, the 8×58mmR Danish Krag (bullet diameter .322 in/8.17mm, bullet weight 237 grains/15.29 grams, muzzle velocity 1,965 ft per second/600 m/s), with the designation 'gevär m/1867-89' used for converted rifles and 'gevär m/1889' used for new rifles.^[7] Rolling block rifles chambered for the 8×58mmR were shorter than the M1867 rifles, with an overall length of 1,240 mm (48.8 in) and a barrel length of 840 mm (33.1 in).^[8]

During the last years of the 19th century the M1867 in all its different guises was finally replaced in Swedish military service by Mauser bolt action repeating rifles and carbines (with a modified Mauser 1893 action), under the designations 'karbin m/1894' and 'gevär m/1896', in caliber 6.5×55mm.

The M1867 rolling block rifle became very popular among civilian hunters in Sweden, particularly for moose hunting, which led to Husqvarna Vapenfabrik producing about 85,000 rifles with the M1867 Remington rolling block action for the civilian market, in addition to the more than 100,000 they made for the armed forces. Surplus military rifles were also sold to civilians, most them being converted to 12.17×44mmR centerfire cartridges.

The M1867 in Norway[edit]

A grand total of 58,450 Remington M1867 were delivered to the Norwegian Armed Forces from 1867 until 1883, when production was curtailed to make room for the Jarmann M1884. All production rifles were meant to be manufactured at Kongsberg Våpenfabrik in Norway, but since the factory needed to be upgraded with more modern machinery, 5000 of the first rifles delivered to the Norwegian Army were manufactured by Husqvarna Vapenfabrik in Sweden in 1871-72. The difference is minor; the Norwegian rifles have brass buttplates and head of the cleaning rod, and steel mounting bands, while Swedish rifles have iron furniture. For the first few years the barrels of the M1867 were made of iron, but after 1871, steel became the standardized material. The price for each barrel was slightly higher, but the better design reduced misfire damage and ultimately resulted in cost effectiveness. Additionally, the designers improved the lock by replacing two lockscrews with a lockplate.

From the early 1870s the Norwegian armed forces used the 12.17×44mm RF, which apart from the case length and overall length of the cartridge was identical to the original Swedish-Norwegian 12.17×42mm RF. In spite of the difference in length the two cartridges were interchangeable and could be chambered and fired in both Norwegian and Swedish rifles. The official military designation for the cartridge was '12mm Remington' from 1879.^[9]

The sight of the rifle was the last item to be standardized because no one could agree on which would be best. The early production rifles had an L-shaped sight that could be flipped over, but the final design was a unique combination of other ideas. Earlier models were supposed to be changed to this final design, but it is still possible to find M1867 with the original sights intact.

Each rifle was delivered with a sling, a long bayonet, a three-pronged screwdriver, an oil bottle, a cleaning rod, and a muzzle plug to stop moisture from getting into the barrel. Early muzzle plugs were a short, conical dowel made of wood, but soon a brass cup with a cut out for the front sight replaced it in service.

In 1880 Kongsberg Våpenfabrikk delivered 72 conversion kits for the rifles which allowed less expensive 22LR ammunition to be fired from the M1867 for training. These kits consisted simply of tubes to be inserted into the rifle from the breech, containing a chamber for the 22LR and a short barrel. The intention was to allow for cheaper training. Later, in 1884, several M1867 were permanently modified to fire 22LR with an improved model of this device.

After the Jarmann M1884 replaced the M1867 as the main rifle in the first lines of the Norwegian Army, the M1867 was delegated to rear units until at least the mid-1890s. Roughly 5,000 were modified in 1888 and 1891 into carbines, firing 8 mm rimmed centerfire ammunition. These remained in use until 1908, when they were finally replaced by Krag–Jørgensen carbines.

From 1900 onwards, the Norwegian Army sold the obsolete M1867 to the public for a nominal price. Many of these were converted into hunting rifles and shotguns, so that it has become difficult to find an M1867 in its original form.

The 8 mm carbine conversions were kept in reserve until World War II, when most of the estimated 4,900 units were destroyed by German forces.

Today, an unmodified M1867 in decent shape might be worth 4,000 - 6,000 Norwegian kroner (roughly 600 - 900 USD), while an M1867 in perfect condition might go for as much as 10,000 kroner (roughly 1,500 USD). However, as mentioned most of the M1867 were modified after they were sold to civilians, and most collectors seem to agree that the modified arms are worth a lot less.

Gallery[edit]

• Swedish-Norwegian rifle m/1867, from the initial batch of M1867 made by Remington in the US

• Swedish rifle m/1867, made by Carl Gustafs Stads Gevärsfaktori

• Swedish rifle m/1867-74, introducing a new more comfortable buttstock

• Swedish rifle m/1867-89 in 8×58mmR Danish Krag centerfire

• Swedish carbine m/1864-68-85 for artillery, train and others

• Norwegian rifle M1867, made by Kongsberg Vaapenfabrik

• A collection of rifles from the Frammuseum, a Remington M1867 at the bottom

References[edit]

1. ^Carsten Schinke - Die leichten schwedischen Infanteriegewehre Armee und Heimwehr - Journal-Verlag Schwend GmbH - 1990
2. ^ ^ab'DigitaltMuseum'. Retrieved 31 May 2015.
3. ^'DigitaltMuseum'. Retrieved 31 May 2015.
4. ^ ^ab'Karbin m'. Retrieved 31 May 2015.
5. ^ ^abCarsten Schinke - Die leichten schwedischen Infanteriegewehre Armee und Heimwehr -Journal-Verlag Schwend GmbH - 1990
6. ^'DigitaltMuseum'. Retrieved 31 May 2015.
7. ^Carsten Schinke - Die leichten schwedischen Infanteriegewehre Armee und Heimwehr -Journal-Verlag Schwend GmbH -1990
8. ^'DigitaltMuseum'. Retrieved 31 May 2015.
9. ^Flatnes, Oyvind. From Musket to Metallic Cartridge: A Practical History of Black Powder Firearms. Crowood Press, 2013, p. 136. ISBN978-1847975935

Remington Rolling Block Number 5

Further reading[edit]

• Hanevik, Karl Egil (1998). Norske Militærgeværer etter 1867. Hanevik Våpen. ISBN82-993143-1-3. Chapter 1 and appendix A
• Oyvind Flatnes (2013). From Musket to Metallic Cartridge: A Practical History of Black Powder Firearms. Crowood Press. pp. 134–139. ISBN978-1847975935.

External links[edit]

I also have a Remington Model 6 that was given to me by my Unclewhom had received it from my Grandfather. As a very youg boy I canremember seeing it in my Grandfathers packhouse. He used it to killrats and vermin around the barn yard. It was in really poor shapewhen I received it but I lovingly restored it. Anyway the model 6was made from 1901-1933 with a total of 497,000 being produced. Arifle in 100% condition is valued at $600, 10% is valued at $75with a 25% increase for a smooth bore barrel. Mine ispriceless.

Answer

I have found over the years that any item is worth only whatsomeone is willing to pay for . Last week, 8/13/05, at a gun showin NC I was offered $250 for my Remington Improved model 6. When Ideclined the dealers offer a bystander offered me $350. I stilldeclined because I didn't really want to sell I just wanted anappraisel. My grandmother bought the gun new and gave it to me in1953, I am giving it to my grandson and wanted to tell him it'svalue.

I have one that is being completely restored, and the offeredvalue at that point is $1000.00 in my area. Not restored it isworth around $300.00.

Remington Rolling Block Rifle Serial Numbers And Dates

Remington Rolling Block Rifle Serial Numbers

Remington Model 4 Serial Numbers

Remington Rolling Block Production Numbers